Description of the stainless steel gas spring 100101
The 100101 stainless steel gas spring is an official Dufour Yachts part, made by Ressorts SPEC (AS Raymond / Barnes Group) for the shipyard. It is a light compression strut: it pushes its rod out with a force of 70 N over a 100 mm stroke, which suits small, light components on board such as locker lids, small hatches, cabinet doors and storage flaps.
The body and rod are made of 316 stainless steel, the reference grade for the marine environment. Unlike carbon steel struts, it does not rust, even with salt air, spray or the condensation found in galleys and lockers. With a 6 mm rod and a 15 mm body, it stays compact and discreet inside joinery. Its 240 mm length (without end fittings) matches the original Dufour installation.
The 100101 has exactly the same dimensions and force as reference 100091, the carbon steel strut that lifts the refrigerator hatch on the Dufour 390. It is the upgrade of choice for owners who want a longer-lasting, corrosion-free part. The strut has an M6 x 1.0 thread at each end and is supplied without end fittings: unscrew the fittings from the worn strut and screw them onto the new one.
Specifications
- Type: Compression gas spring
- Reference: 100101
- Force: 70 N
- Stroke: 100 mm
- Length (extended, without end fittings): 240 mm
- Rod diameter: 6 mm
- Body diameter: 15 mm
- Thread: M6 x 1.0 at both ends
- End fittings: not included
- Material: 316 stainless steel body and rod
Boat compatibility
- Brand: DUFOUR – official Dufour Yachts part, reference 100101
- Equivalent reference: 100091 (same dimensions and force, carbon steel – refrigerator hatch, Dufour 390)
Installation / Maintenance
Installation:
- Hold the lid open, unscrew the end fittings from the worn strut and screw them onto the 100101.
- Mount the strut with the rod pointing down where possible to keep the seal lubricated.
- Check that the lid opens fully and closes without binding or side load on the rod.
Maintenance:
- Rinse with fresh water from time to time and keep the rod clean. Never scratch or paint it, as this damages the seal.
- Never heat, open or drill the body, which is pressurised.
- A strut that no longer holds the lid open must be replaced: it cannot be refilled.
Our review
✔️ Pros :
- Official Dufour Yachts part: exact original fit.
- 316 stainless steel: no rust, even in exposed locations.
- Direct stainless upgrade for the 100091.
- Lets you reuse your existing end fittings.
❌ Cons :
- End fittings not included.
- Fixed 70 N force, for light lids only.
- More expensive than the carbon steel 100091.
Conclusion
If your Dufour has a strut printed 100101 or 100091, or one that measures 240 mm with a 100 mm stroke and a 70 N force, the 100101 is the right replacement. Choose it over the 100091 if you want a part that will not rust. Keep your existing M6 end fittings or order new ones separately. If in doubt, contact our team with your boat’s details before ordering.
Good to Know
- Official Dufour Yachts part.
- Before ordering, compare three values: length (240 mm), stroke (100 mm) and force (70 N).
- Supplied without end fittings: M6 x 1.0 thread at both ends.
- Carbon steel version with the same dimensions: 100091.
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift

English spoken
On parle Français

Reviews
There are no reviews yet.