Description of the stainless steel gas spring 100117
The 100117 stainless steel gas spring is an official Dufour Yachts part, made by Ressorts SPEC (AS Raymond / Barnes Group) and fitted as original equipment on Dufour sailing yachts. It is a compression strut: it pushes its rod out with a force of 300 N over a long 300 mm stroke, giving smooth opening assistance and a steady hold for medium-to-large components on board, such as cockpit lockers, deck hatches and berth lids.
The body and rod are made of 316 stainless steel, the reference grade for the marine environment. This makes the strut resistant to rust in salt air, spray and the humidity of lockers. With a 10 mm rod and a 23 mm body, it is sized for long strokes and frequent use. The body measures 649 mm, and the overall length between ball socket centres is 687 mm when extended.
Both ends are threaded M8 x 1.25 and fitted with stainless steel ball sockets that clip directly onto standard 10 mm ball studs. They let the strut swivel freely as the hatch moves through its arc, which limits side loads on the rod and seal. The 100117 is delivered ready to install: unclip the worn strut and clip the new one onto the original studs, with no modification to the existing fixings.
Specifications
- Type: Compression gas spring with ball sockets
- Reference: 100117
- Force: 300 N
- Stroke: 300 mm
- Body length (extended, without end fittings): 649 mm
- Length between centres (extended, with end fittings): 687 mm
- Rod diameter: 10 mm
- Body diameter: 23 mm
- Thread: M8 x 1.25 at both ends
- Material: 316 stainless steel body and rod
End fittings & boat compatibility
- End fittings #1 and #2: EFBS009S ball socket, 304/303 stainless steel, for 10 mm ball stud, M8 x 1.25, length 19 mm
- Brand: DUFOUR – official Dufour Yachts part, reference 100117
- Matching bracket: 100108 stainless steel angle bracket with 10 mm ball stud
Installation / Maintenance
Installation:
- Prop the hatch open, unclip the worn strut from its ball studs and clip the 100117 in its place.
- Mount the strut with the rod pointing down where possible to keep the seal lubricated.
- Check that the hatch opens fully and closes without binding or side load on the rod.
Maintenance:
- Rinse with fresh water after sailing and keep the rod clean. Salt crystals on the rod can damage the seal.
- Check the ball sockets periodically.
- Never heat, open or drill the body, which is pressurised. A strut that has lost force must be replaced.
Our review
✔️ Pros :
- Official Dufour Yachts part: exact original fit.
- All-stainless construction: body, rod and ball sockets.
- Long 300 mm stroke for large hatches and lockers.
- Delivered with ball sockets, ready to clip on.
❌ Cons :
- Fixed force of 300 N, not adjustable.
- Fits 10 mm ball studs only.
- Long format: requires 687 mm between centres at full extension.
Conclusion
If your Dufour has a strut printed 100117, or one that measures 687 mm between centres with a 300 mm stroke, a 300 N force and 10 mm ball sockets, this is the right replacement. Its all-stainless construction suits exposed locations such as deck hatches and cockpit lockers. If a mounting bracket is also damaged, add the matching 100108 bracket to your order. If any value differs from your original strut, contact our team before ordering.
Good to Know
- Official Dufour Yachts part.
- Before ordering, compare three values: length between centres (687 mm), stroke (300 mm) and force (300 N).
- End fittings: EFBS009S stainless ball sockets for 10 mm ball studs.
- Matching bracket: 100108 (stainless steel, 10 mm ball).
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift



English spoken
On parle Français

Reviews
There are no reviews yet.