Description of the gas spring 100091
The 100091 gas spring is an official Dufour Yachts part, made by Ressorts SPEC (AS Raymond / Barnes Group) and fitted as original equipment on the Dufour 390 sailing yacht, where it lifts and holds open the refrigerator hatch. It is a light compression strut: it pushes its rod out with a force of 70 N over a 100 mm stroke, enough to open the fridge lid easily and keep it raised while you reach inside, even with the boat heeling or rolling at anchor.
This gas strut belongs to the Ressorts SPEC Nitrider range. It has a black-coated body and a rod with a nitrided anti-corrosion surface, and it uses a modern sealing system designed for long service life. The 6 mm rod and 15 mm body keep it compact and discreet inside the galley joinery, while the 240 mm length (without end fittings) matches the original Dufour installation exactly.
After years of daily use, a refrigerator hatch strut gradually loses pressure. The lid becomes heavy to lift or no longer stays open, which is impractical and can be unsafe at sea. Replacing it with the original 100091 restores the hatch’s smooth opening. The strut has an M6 x 1.0 thread at each end and is supplied without end fittings: simply unscrew the fittings from the worn strut and screw them onto the new one. For owners who prefer a fully corrosion-resistant part, reference 100101 offers the same dimensions and force in stainless steel.
Specifications
- Type: Compression gas spring
- Reference: 100091
- Application: refrigerator hatch lift
- Force: 70 N
- Stroke: 100 mm
- Length (extended, without end fittings): 240 mm
- Rod diameter: 6 mm
- Body diameter: 15 mm
- Thread: M6 x 1.0 at both ends
- End fittings: not included
- Finish: black-coated body, nitrided anti-corrosion rod
Boat compatibility
- Brand: DUFOUR – official Dufour Yachts part, reference 100091
- Compatible model: Dufour 390
- Location on board: refrigerator hatch (galley)
- Stainless steel alternative: 100101 (same dimensions and force)
Installation / Maintenance
Installation:
- Hold the refrigerator hatch open, then unscrew the end fittings from the worn strut and screw them onto the 100091.
- Mount the strut with the rod pointing down where possible to keep the seal lubricated.
- Check that the fridge lid opens fully and closes tightly, without binding or side load on the rod.
Maintenance:
- Keep the rod clean and free of salt or food residue. Never scratch or paint it, as this damages the seal.
- Never heat, open or drill the body, which is pressurised.
- A strut that no longer holds the hatch open must be replaced: it cannot be refilled.
Our review
✔️ Pros :
- Official Dufour Yachts part: exact original fit on the Dufour 390.
- Force sized for the refrigerator hatch: easy opening, stable hold.
- Nitrided rod with anti-corrosion surface.
- Lets you reuse your existing end fittings.
❌ Cons :
- End fittings not included.
- Fixed 70 N force, for light hatches only.
- Not stainless steel: for a fully corrosion-resistant part, prefer the 100101.
Conclusion
If the refrigerator hatch on your Dufour 390 no longer stays open, or has become heavy to lift, the 100091 is the official Dufour Yachts replacement. Check that your current strut measures 240 mm with a 100 mm stroke and a 70 N force, then keep your existing M6 end fittings. If you prefer a stainless steel part, choose the 100101, which has the same dimensions. If in doubt, contact our team with your boat’s details before ordering.
Good to Know
- Official Dufour Yachts part. Lifts the refrigerator hatch on the Dufour 390.
- Before ordering, compare three values: length (240 mm), stroke (100 mm) and force (70 N).
- Supplied without end fittings: M6 x 1.0 thread at both ends.
- Stainless steel version with the same dimensions: 100101.
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift



English spoken
On parle Français

Reviews
There are no reviews yet.