Electric table lift kit NL2389-PAIRE-TB – Pair of 3-stage aluminium legs – 24V DC
The NL2389-PAIRE-TB electric table lift kit is a complete, ready-to-install solution for motorizing a large table aboard yachts, motor boats and catamarans fitted with a 24V DC network. Designed as an electric table lifter for boats, it pairs two NL2389 electric table legs with the control box, remote control and switch they need, so the shipyard or owner orders a single reference with every component matched.
Each motorized table pedestal is a 3-stage, rectangular-section aluminium column with a clear anodized finish. It offers a 400 mm stroke, from 358 mm retracted to 758 mm fully extended, and stops at any height in between. The same table can therefore serve as a dining table, a coffee table or a base for converting the cockpit seating into a sundeck. Rated IP55, these telescopic table columns can be installed in the saloon as well as in the cockpit or on the flybridge.
The heart of this automated table lift is the NL2120 control box. It reads the position of both columns and keeps them moving in step, so the tabletop stays level throughout its travel, without mechanical stress on the furniture or on the pedestals. The NL2120 also houses a radio receiver for the AT5189 4-channel remote control, while the NL1494 rocker switch adds a wired, momentary control point on a bulkhead or a helm console.
The two power table bases are fixed with 200 x 200 x 8 mm plates, top and bottom, for a stable mounting on the cabin sole or cockpit floor. Each column accepts a dynamic load of 50 kg and a static load of 100 kg, rising to 200 kg with compression locking.
Kit contents
- 2 x NL2389: 3-stage rectangular aluminium table lifters, 24V DC, IP55
- 1 x NL2120: synchronization control box with integrated radio receiver
- 1 x AT5189: 4-channel radio remote control
- 1 x NL1494: momentary (on)/off/(on) rocker switch
Specifications
Table columns (x2):
- Type: 3-stage telescopic table column, rectangular section
- Power supply: 24V DC
- Retracted height: 358 mm (14.09″)
- Max. height: 758 mm (29.84″)
- Stroke: 400 mm (15.75″)
- Mounting plates (top / bottom): 200 x 200 x 8 mm (7.87 x 7.87 x 0.31″)
- Dynamic load per column: 50 kg
- Static load per column: 100 kg (200 kg with compression locking)
- Speed: 18 mm/s no load, 9 mm/s under load
- Protection rating: IP55 – indoor or outdoor installation
- Material: 20-micron clear anodized aluminium
- Weight per column: 11.2 kg (24.7 lbs)
Controls:
- NL2120 control box: 12/24V DC, 2 motor outputs, synchronization by microswitch, integrated radio receiver, case 180 x 94 x 57 mm
- AT5189 remote control: 4-channel radio transmitter, HCS
- NL1494 switch: momentary (on)/off/(on), IP66 front face, flush mount in a 30 x 22 mm cut-out
Installation / Maintenance
Installation:
- Fix both columns to a rigid structure using the top and bottom mounting plates.
- Fit the NL2120 in a dry, ventilated location protected from spray, close to the pedestals (under a bench, in a locker or beneath the table).
- Keep each motor cable under 5 metres, and use cables of equal length on both sides for correct synchronization.
- Protect the 24V supply line with a fuse or breaker as specified by NOVAL.
- Set the NL2120 microswitches to synchronized mode before powering up.
Maintenance:
- Rinse the aluminium surfaces regularly with fresh water.
- Apply silicone spray or lanolin to the moving parts to limit friction.
- Periodically check connectors and cables for corrosion, chafing or loose terminals.
Our review
✔️ Pros :
- Complete kit: columns, control box, remote control and switch under one reference.
- Synchronized movement keeps large tabletops level.
- IP55 rating: suitable for saloon, cockpit or flybridge.
- Two control options supplied: wireless remote and wired switch.
❌ Cons :
- 24V DC only – for a 12V network, choose the NL2388-PAIRE-TB kit.
- Motor cables limited to 5 m and must be of equal length.
- Dynamic load limited to 50 kg per column.
Conclusion
The NL2389-PAIRE-TB is the simplest way to motorize a large table on a 24V DC boat: every component is matched and supplied together, with no risk of choosing an incompatible control box. Its IP55 rating allows installation in the saloon as well as in the cockpit or on the flybridge. It suits shipyards equipping a new model as well as owners upgrading a manual or gas-assisted table during a refit. Before ordering, check that your onboard network is 24V, that the tabletop and its expected use stay within 50 kg dynamic load per column, and that both pedestals can be placed within 5 m of the control box. For a 12V boat, choose the NL2388-PAIRE-TB kit. For a single-pedestal table, a single NL2389 with its own control is more appropriate.
Good to Know
- Kit powered by 24V DC. The NL2388-PAIRE-TB is the 12V DC version, built around two NL2388 columns.
- The NL2120 synchronization can be disabled by microswitch to drive the two columns independently.
- IP55-rated columns: indoor or outdoor installation; avoid direct, prolonged exposure to water.
- Dry-contact operation: compatible with NMEA 2000 and CAN bus monitoring systems through a converter box.
- Standard finish: clear anodized aluminium.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift




English spoken
On parle Français

Reviews
There are no reviews yet.