Description of the compression damper 100113-B – Stroke 102 mm – 316 stainless steel
The 100113-B compression damper is a hydraulic motion-control component designed for marine joinery and deck fittings. Unlike a gas spring, it produces no thrust force. Its only role is to slow the closing movement in a controlled way, and the rod is left free to extend. On board, this means a lid, hatch or locker door that closes gently instead of dropping or slamming. This protects the hinges, the surrounding gelcoat and the crew’s fingers.
Manufactured by Associated Spring Raymond (UK), the damper is built with a rod, tube and end plugs in 316 stainless steel. This marine-grade alloy is the standard choice for components exposed to salt spray, humidity and the temperature swings typical of a cockpit or cabin. The slim 15 mm body and 6 mm rod make it easy to fit into tight spaces, such as under seats, in chart tables or inside cockpit lockers.
This reference is an original part supplied to Dufour Yachts. It allows owners and refit yards to restore the original behaviour of the fitting with an identical replacement, without modifying the brackets or the geometry.
Specifications
- Type: Compression damper (damped closing, free extension)
- Overall length (extended): 281 mm
- Closed length: 179 mm
- Stroke: 102 mm
- Body diameter: 15 mm
- Rod diameter: 6 mm
- Damping in compression: 58 mm/s under a 180 N load
- Damping in extension: free movement
- Thrust force: none (damping only)
- End connections: M6 male thread on both ends
- Materials: rod, tube and plugs in 316 stainless steel
- Supply: delivered without end fittings
Installation / Maintenance
Installation:
- Check the extended length (281 mm), the closed length (179 mm) and the M6 threads against the part being replaced before fitting.
- Reuse your existing M6 end fittings or brackets, or order new ones separately. The damper is supplied without end fittings.
- Install it in the same orientation and on the same anchor points as the original part, so the damping acts during the closing movement.
- Make sure the damper is never used as an end stop. The hinge or a mechanical stop must take the load at the end of travel.
Maintenance:
- Rinse with fresh water after exposure to salt spray, and keep the rod clean and free of scratches.
- Never grease or paint the rod, and do not use it as a handle.
- If the damping weakens or the lid closes too quickly, replace the damper. A sealed hydraulic unit cannot be serviced.
Our review
✔️ Pros :
- Full 316 stainless steel construction, suited to the marine environment.
- Original Dufour part, a like-for-like replacement with identical dimensions.
- Smooth, controlled closing that protects hinges and joinery.
- Compact 15 mm body, easy to fit into confined spaces.
❌ Cons :
- No thrust force: it does not lift or hold a hatch open.
- Supplied without end fittings.
- Fixed damping rate, which cannot be adjusted.
Conclusion
The 100113-B is the right choice if your original damper has lost its braking effect or is leaking, and the lid or locker it controls now drops too fast. Its dimensions (281 / 179 mm, 102 mm stroke, M6 threads) and its 316 stainless steel construction make it an exact replacement for the original part on Dufour sailboats. However, if your hatch needs to be lifted or held open, you need a gas spring, not a damper. If in doubt, send us a photo of the label on your existing part and we will help you identify the correct reference.
Good to Know
- Compression damper: braked closing (58 mm/s under 180 N), free opening.
- Identification: the reference 100113-B is printed on the label of the body.
- M6 threads on both ends – end fittings not included.
- Original equipment on Dufour Yachts sailboats.
- Need help with identification? Contact us at contact@nauticspares.com or on WhatsApp +33 6 33 30 44 50.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift




English spoken
On parle Français

Reviews
There are no reviews yet.