Description of the gas spring 081493
The 081493 gas spring is a stainless steel gas strut with ball sockets made by Ressorts SPEC (AS Raymond / Barnes Group) and supplied as original equipment to the Beneteau group through BJ Technologie. It is a compression strut: it pushes its rod out with a force of 300 N over a long 400 mm stroke, giving controlled opening assistance and a stable hold for large or deep components on board, such as cockpit lockers, deck hatches and lazarette lids.
The body and rod are made of stainless steel, which makes this marine gas spring well suited to the conditions found on a boat: salt-laden air, spray and humidity in lockers. With a 10 mm rod and a 23 mm body, it is sized for long strokes while staying compact enough for joinery and deck mouldings. The body measures 849 mm, and the overall length between ball socket centres is 909 mm when extended.
Both ends are threaded M8 x 1.25 and come fitted with stainless steel ball sockets with stainless spring clips. They clip directly onto standard 10 mm ball studs and let the strut swivel freely as the hatch opens and closes. The 081493 is delivered ready to install, so you can swap the worn strut for the new one in a few minutes without modifying the original fixings.
Specifications
- Type: Compression gas spring with ball sockets
- Reference: 081493
- Force: 300 N
- Stroke: 400 mm
- Body length (extended, without end fittings): 849 mm
- Length between centres (extended, with end fittings): 909 mm
- Rod diameter: 10 mm
- Body diameter: 23 mm
- Thread: M8 x 1.25 at both ends
- Material: stainless steel body and rod
End fittings & compatibility
- End fittings #1 and #2: EFBS006S stainless steel ball socket, M8 x 1.25, length 30 mm, stainless spring clip
- Compatible ball diameter: 10 mm
- Original equipment: Beneteau group (BJ Technologie)
- Nitrided alternative: 081494 (same dimensions and force, black body)
Installation / Maintenance
Installation:
- Hold the hatch open, unclip the worn strut from its ball studs and clip the 081493 in its place.
- Mount the strut with the rod pointing down where possible to keep the seal lubricated.
- Check that the hatch opens fully and closes without binding or side load on the rod.
Maintenance:
- Rinse with fresh water after sailing and keep the rod clean. Salt crystals on the rod can damage the seal.
- Periodically check the ball sockets and their spring clips.
- Never heat, open or drill the body, which is pressurised. A strut that has lost force must be replaced.
Our review
✔️ Pros :
- Stainless steel body, rod and ball sockets for marine durability.
- Original equipment for the Beneteau group: exact original fit.
- Long 400 mm stroke for large hatches and lockers.
- Delivered with ball sockets, ready to clip on.
❌ Cons :
- Fixed force of 300 N, not adjustable.
- Fits 10 mm ball studs only.
- Long format: requires 909 mm between centres at full extension.
Conclusion
If your boat has a strut printed 081493, or one that measures 909 mm between centres with a 400 mm stroke, a 300 N force and 10 mm ball sockets, this is the right replacement. Its stainless construction suits exposed locations such as deck hatches and cockpit lockers. For an interior installation or a tighter budget, the nitrided 081494 has the same dimensions. If any value differs from your original strut, contact our team before ordering.
Good to Know
- Original equipment for the Beneteau group (BJ Technologie).
- Before ordering, compare three values: length between centres (909 mm), stroke (400 mm) and force (300 N).
- End fittings: EFBS006S stainless ball sockets for 10 mm ball studs.
- Nitrided version with the same dimensions: 081494.
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift



English spoken
On parle Français

Reviews
There are no reviews yet.