Description of the gas spring 081633
The 081633 gas spring is a compression strut made by Ressorts SPEC (AS Raymond / Barnes Group) and supplied as original equipment to the Beneteau group through BJ Technologie. It pushes its rod out with a force of 500 N over a 250 mm stroke, giving firm opening assistance and a secure hold for heavy components on board, such as cockpit lockers, deck hatches and berth lids with storage underneath.
This marine gas strut belongs to the Ressorts SPEC Nitrider range. It has a carbon steel body with a black e-coat and a rod with a black nitrided anti-corrosion surface, plus a modern sealing system designed for long service life. With an 8 mm rod and an 18 mm body, it delivers high force in a compact size. The body measures 549 mm, and the overall length between ball socket centres is 585 mm when extended.
Both ends are threaded M6 x 1.0 and fitted with black nylon (PA66 glass-filled) ball sockets that clip directly onto standard 10 mm ball studs. These sockets are rated well above the strut’s force, and they let it swivel freely as the hatch opens and closes. The 081633 is delivered ready to install: unclip the worn strut and clip the new one onto the original studs in a few minutes.
Specifications
- Type: Compression gas spring with ball sockets
- Reference: 081633
- Force: 500 N
- Stroke: 250 mm
- Body length (extended, without end fittings): 549 mm
- Length between centres (extended, with end fittings): 585 mm
- Rod diameter: 8 mm
- Body diameter: 18 mm
- Thread: M6 x 1.0 at both ends
- Finish: black e-coat carbon steel body, black nitrided rod
End fittings & compatibility
- End fittings #1 and #2: EFBS004P ball socket, black nylon PA66 GF30, for 10 mm ball stud, length 18 mm
- Original equipment: Beneteau group (BJ Technologie)
- Lighter version: 081635 (same dimensions, 300 N)
Installation / Maintenance
Installation:
- Prop the hatch open securely, unclip the worn strut from its ball studs and clip the 081633 in its place.
- Mount the strut with the rod pointing down where possible to keep the seal lubricated.
- Check that the hatch opens fully and closes without binding or side load on the rod.
Maintenance:
- Keep the rod clean and free of salt deposits. Never scratch or paint it, as this damages the seal.
- Check the nylon ball sockets periodically for wear or cracks.
- Never heat, open or drill the body, which is pressurised. A strut that has lost force must be replaced.
Our review
✔️ Pros :
- Original equipment for the Beneteau group: exact original fit.
- High 500 N force in a compact 8/18 mm format.
- Delivered with ball sockets, ready to clip on.
- Nitrided rod with anti-corrosion surface.
❌ Cons :
- Not stainless steel: less suited to permanently exposed outdoor locations.
- Fixed force of 500 N, not adjustable.
- Fits 10 mm ball studs only.
Conclusion
If your boat has a strut printed 081633, or one that measures 585 mm between centres with a 250 mm stroke, a 500 N force and 10 mm ball sockets, this is the right replacement. Check the force printed on your original strut carefully: the 081635 has exactly the same dimensions but only 300 N, and fitting the wrong one will make the hatch too stiff or too weak. If in doubt, contact our team before ordering.
Good to Know
- Original equipment for the Beneteau group (BJ Technologie).
- Before ordering, compare three values: length between centres (585 mm), stroke (250 mm) and force (500 N).
- Same dimensions, lower force: 081635 (300 N).
- End fittings: EFBS004P nylon ball sockets for 10 mm ball studs.
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift



English spoken
On parle Français

Reviews
There are no reviews yet.