Description of the stainless steel gas spring 081631
The 081631 stainless steel gas spring is a compression strut made by Ressorts SPEC (AS Raymond / Barnes Group) and supplied as original equipment to the Beneteau group through BJ Technologie. It pushes its rod out with a force of 200 N over a 220 mm stroke, giving smooth opening assistance and a steady hold for medium-weight components on board, such as lockers, hatches and seat lids.
The body and rod are made of 316 stainless steel, the reference grade for the marine environment. This makes the strut resistant to rust in salt air, spray and the humidity of lockers and bilges. With an 8 mm rod and an 18 mm body, it stays compact and discreet in joinery and mouldings. The body measures 489 mm, and the overall length between fitting centres is 526 mm when extended.
This marine gas strut has a specific configuration with a different fitting at each end. On one end, a black nylon (PA66 glass-filled) ball socket clips onto a 10 mm ball stud. On the other, an electropolished 304 stainless steel eye with an 8 mm hole is fixed with a pin or bolt. Both fittings are on M6 x 1.0 threads. This mixed setup matches the original installation, so the 081631 can replace the worn strut without changing the brackets on board.
Specifications
- Type: Compression gas spring
- Reference: 081631
- Force: 200 N
- Stroke: 220 mm
- Body length (extended, without end fittings): 489 mm
- Length between centres (extended, with end fittings): 526 mm
- Rod diameter: 8 mm
- Body diameter: 18 mm
- Thread: M6 x 1.0 at both ends
- Material: 316 stainless steel body and rod
End fittings & compatibility
- End fitting #1: EFBS004P ball socket, black nylon PA66 GF30, for 10 mm ball stud, length 18 mm
- End fitting #2: EFE009S eye, 304 stainless steel electropolished, Ø8 mm hole, length 25 mm, thickness 3 mm
- Original equipment: Beneteau group (BJ Technologie)
Installation / Maintenance
Installation:
- Hold the hatch open, then remove the worn strut: unclip the ball socket and remove the pin or bolt from the eye.
- Fit the 081631 with the same orientation as the original, preferably with the rod pointing down.
- Check that the hatch opens fully and closes without binding or side load on the rod.
Maintenance:
- Rinse with fresh water from time to time and keep the rod clean. Salt crystals on the rod can damage the seal.
- Check the nylon ball socket and the eye fixing periodically.
- Never heat, open or drill the body, which is pressurised. A strut that has lost force must be replaced.
Our review
✔️ Pros :
- 316 stainless steel body and rod for marine durability.
- Original equipment for the Beneteau group: exact original fit.
- Supplied with both end fittings, ready to install.
- Compact format for joinery and lockers.
❌ Cons :
- Mixed fittings (ball socket + eye): check both mounting points before ordering.
- Fixed force of 200 N, not adjustable.
- The ball socket is nylon, not stainless steel.
Conclusion
If your boat has a strut printed 081631, or one that measures 526 mm between centres with a 220 mm stroke, a 200 N force, a ball socket on one end and an eye on the other, this is the right replacement. If your strut has the same fitting at both ends, or if any value differs, this reference will not fit. Contact our team with a photo of your original strut before ordering if in doubt.
Good to Know
- Original equipment for the Beneteau group (BJ Technologie).
- Before ordering, compare three values: length between centres (526 mm), stroke (220 mm) and force (200 N).
- Two different end fittings: a ball socket for a 10 mm ball stud and an eye for an 8 mm pin.
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift



English spoken
On parle Français

Reviews
There are no reviews yet.