Description of the gas spring 081496
The 081496 gas spring is a heavy-duty gas strut with ball joints made by Ressorts SPEC (AS Raymond / Barnes Group) and supplied as original equipment to the Beneteau group through BJ Technologie. It is a compression strut: it pushes its rod out with a force of 500 N over a long 500 mm stroke, giving powerful opening assistance and a secure hold for large, heavy components on board, such as engine hatches, deck hatches and cockpit lockers.
This marine gas spring belongs to the Ressorts SPEC Nitrider range. It has a black-coated body and a rod with a nitrided anti-corrosion surface, and it uses a modern sealing system designed for long service life. With a 14 mm rod and a 28 mm body, it is one of the largest formats in the range, built for loads and strokes beyond the reach of standard struts. The body measures 1066 mm, and the overall length between joint centres is 1136 mm when extended.
Both ends are threaded M10 x 1.5 and come fitted with 16 mm ball joints. Each joint includes its own ball stud with an M10 x 1.5 male thread and a lock nut, so it bolts directly through the mounting brackets. The ball joints let the strut swivel freely as the hatch moves through its arc, which limits side loads on the rod and seal. The 081496 is delivered complete and ready to install.
Specifications
- Type: Compression gas spring with ball joints
- Reference: 081496
- Force: 500 N
- Stroke: 500 mm
- Body length (extended, without end fittings): 1066 mm
- Length between centres (extended, with end fittings): 1136 mm
- Rod diameter: 14 mm
- Body diameter: 28 mm
- Thread: M10 x 1.5 at both ends
- Finish: black-coated body, nitrided anti-corrosion rod
End fittings & compatibility
- End fittings #1 and #2: EFBJ010Z ball joint, 16 mm ball, zinc-plated steel, length 35 mm
- Ball stud: included, M10 x 1.5 male thread (20 mm) with lock nut
- Original equipment: Beneteau group (BJ Technologie)
Installation / Maintenance
Installation:
- Prop the hatch securely open before removing the old strut: at 500 N, an unsupported hatch can drop suddenly.
- Bolt the ball studs through the existing brackets and tighten the lock nuts.
- Mount the strut with the rod pointing down where possible to keep the seal lubricated.
- Check that the hatch opens fully and closes without binding or side load on the rod.
Maintenance:
- Keep the rod clean and free of salt deposits. Never scratch or paint it, as this damages the seal.
- Check the lock nuts and ball joints regularly, especially after rough passages.
- Never heat, open or drill the body, which is pressurised. A strut that has lost force must be replaced.
Our review
✔️ Pros :
- Original equipment for the Beneteau group: exact original fit.
- 500 N force and 500 mm stroke for large, heavy hatches.
- Delivered complete with ball joints, studs and lock nuts.
- Nitrided rod with anti-corrosion surface.
❌ Cons :
- Not stainless steel: zinc-plated joints are less suited to permanently exposed locations.
- Fixed force of 500 N, not adjustable.
- Long format: requires 1136 mm between centres at full extension.
Conclusion
If your boat has a strut printed 081496, or one that measures 1136 mm between centres with a 500 mm stroke, a 500 N force and 16 mm ball joints, this is the right replacement. It is supplied complete with its ball studs, so you can fit it straight onto the original brackets. If your strut is shorter, weaker or uses ball sockets instead of ball joints, this reference will not fit. Contact our team to identify the correct gas spring before ordering.
Good to Know
- Original equipment for the Beneteau group (BJ Technologie).
- Before ordering, compare three values: length between centres (1136 mm), stroke (500 mm) and force (500 N).
- End fittings: EFBJ010Z 16 mm ball joints with M10 studs and lock nuts, included.
- Always support the hatch during replacement: it is heavy.
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift



English spoken
On parle Français

Reviews
There are no reviews yet.