Description of the gas spring 100107
The 100107 gas spring is an official Dufour Yachts part, made by Ressorts SPEC (AS Raymond / Barnes Group) to the shipyard’s specification and fitted as original equipment on Dufour sailing yachts. It is a traction (tension) strut: at rest the rod is retracted, and the strut pulls its two fixing points together with a force of 800 N. Pulling the ends apart extends it over a 400 mm stroke, from 550 mm to 950 mm between ball socket centres.
On sailing yachts and motor boats, this pulling action gives controlled closing and opening assistance on heavy components such as companionway doors, cockpit lockers and deck hatches, where a compression strut cannot be fitted the right way round. The body, rod, end fittings and plugs are all made of AISI 316 stainless steel, the reference grade for the marine environment. This gives good resistance to salt air, spray and condensation in lockers and under the deck.
The tension gas strut has a 28 mm diameter body and a 10 mm rod. A 23 mm additional internal rod support guides the rod over its long stroke and keeps the strut steady at full extension. This is the main improvement over the previous reference 100099, which has the same dimensions and force and which the 100107 replaces directly. Both ends are threaded M8 x 1.25 and fitted with EFBS011X ball sockets for a firm, quiet connection that clips onto standard 13 mm ball studs. The reference is printed on the body for easy identification.
Specifications
- Type: Traction (tension) gas spring
- Reference: 100107 (replaces 100099)
- Force: 800 N
- Stroke: 400 mm
- Length at rest (retracted, between centres): 550 mm (± 2 mm)
- Extended length (between centres): 950 mm (± 2 mm)
- Body diameter: 28 mm
- Rod diameter: 10 mm
- Rod guidance: 23 mm additional internal rod support
- Material: 316 stainless steel body, rod, end fittings and plugs
End fittings & compatibility
- End fitting #1: EFBS011X ball socket, 13 mm, M8 x 1.25, length 25 mm, stainless steel with stainless spring clip
- End fitting #2: EFBS011X ball socket, 13 mm, M8 x 1.25, length 25 mm, stainless steel with stainless spring clip
- Compatible ball diameter: 13 mm
- Compatible mounting brackets (13 mm ball): EFBR09S stainless steel bracket (2 mm thick, 5.1 mm fixing holes), the original Dufour bracket; EFBR12S stainless steel bracket (3 mm thick, 5.5 mm fixing holes)
- Original equipment: Dufour Yachts
Dufour compatibility
- Official part: Dufour Yachts original equipment, reference 100107 (replaces 100099)
Installation / Maintenance
Installation:
- Check the orientation: the 100107 pulls its ends together and does not push them apart like a standard gas strut.
- The distance between the two ball stud centres must stay between 550 mm and 950 mm over the whole movement.
- Snap the sockets onto clean 13 mm ball studs fixed to a rigid structure, preferably in stainless steel to avoid galvanic corrosion.
- Check that the hatch or door moves through its full arc without binding or side load on the rod.
Maintenance:
- Rinse with fresh water after sailing and keep the rod clean. Salt crystals on the rod can damage the seal.
- Periodically check the ball sockets and their spring clips.
- Never paint, heat, open or drill the cylinder, which is pressurised. A strut that has lost force must be replaced.
Our review
✔️ Pros :
- Fully 316 stainless steel, including end fittings and plugs.
- Original Dufour Yachts part, direct replacement for the 100099.
- Internal rod support for stable movement over the 400 mm stroke.
- Supplied with ball sockets, ready to clip on.
❌ Cons :
- Fixed force of 800 N, not adjustable.
- Not interchangeable with a standard push-type gas spring.
- Requires 13 mm ball studs: smaller 10 mm studs will not fit.
Conclusion
If your Dufour has a strut printed 100107 or 100099, or one that measures 550 mm at rest and 950 mm extended with an 800 N pulling force, this is the right part to order. It fits the original 13 mm ball studs and EFBR09S brackets without modification. If your strut pushes rather than pulls, or uses different dimensions or 10 mm ball studs, this reference will not fit. Contact our team to identify the correct gas spring before ordering.
Good to Know
- Official Dufour Yachts part. Compatible boats: [Dufour model 1], [Dufour model 2].
- Before ordering, compare three values: length at rest (550 mm), stroke (400 mm) and force (800 N).
- Replaces reference 100099, with the same dimensions and force.
- End fittings: EFBS011X ball sockets for 13 mm ball studs, matching EFBR09S / EFBR12S brackets.
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift

English spoken
On parle Français

Reviews
There are no reviews yet.