Description of the stainless steel gas spring 100098
The 100098 stainless steel gas spring is an official Dufour Yachts part, made by Ressorts SPEC (AS Raymond / Barnes Group) and fitted as original equipment on Dufour sailing yachts. It is a compression strut: it pushes its rod out with a force of 160 N over a 120 mm stroke, giving smooth opening assistance and a steady hold for light-to-medium components on board, such as locker lids, cabinet doors and small hatches.
The body and rod are made of 316 stainless steel, the reference grade for the marine environment. The strut does not rust, even when exposed to salt air, spray or the condensation found in lockers and galleys. With a 6 mm rod and a 15 mm body, it is slim and discreet inside joinery. Its 280 mm length (without end fittings) matches the original Dufour installation.
The 100098 has an M6 x 1.0 thread at each end and is supplied without end fittings: unscrew the fittings from the worn strut and screw them onto the new one. Dufour also uses reference 100097, which has the same dimensions but a higher 200 N force. Check the force printed on your original strut so the lid is neither too stiff nor too weak.
Specifications
- Type: Compression gas spring
- Reference: 100098
- Force: 160 N
- Stroke: 120 mm
- Length (extended, without end fittings): 280 mm
- Rod diameter: 6 mm
- Body diameter: 15 mm
- Thread: M6 x 1.0 at both ends
- End fittings: not included
- Material: 316 stainless steel body and rod
Boat compatibility
- Brand: DUFOUR – official Dufour Yachts part, reference 100098
- Same dimensions, higher force: 100097 (200 N)
Installation / Maintenance
Installation:
- Hold the lid open, unscrew the end fittings from the worn strut and screw them onto the 100098.
- Mount the strut with the rod pointing down where possible to keep the seal lubricated.
- Check that the lid opens fully and closes without binding or side load on the rod.
Maintenance:
- Rinse with fresh water from time to time and keep the rod clean. Never scratch or paint it, as this damages the seal.
- Never heat, open or drill the body, which is pressurised.
- A strut that no longer holds the lid open must be replaced: it cannot be refilled.
Our review
✔️ Pros :
- Official Dufour Yachts part: exact original fit.
- 316 stainless steel: no rust, even in exposed locations.
- Slim 6/15 mm format, discreet in joinery.
- Lets you reuse your existing end fittings.
❌ Cons :
- End fittings not included.
- Fixed 160 N force, not adjustable.
- Easily confused with the 100097 (same size, 200 N): check the force.
Conclusion
If your Dufour has a strut printed 100098, or one that measures 280 mm with a 120 mm stroke and a 160 N force, this is the right replacement. If the lid needs more support, or your original strut is marked 200 N, choose the 100097 instead. Keep your existing M6 end fittings or order new ones separately. If in doubt, contact our team before ordering.
Good to Know
- Official Dufour Yachts part.
- Before ordering, compare three values: length (280 mm), stroke (120 mm) and force (160 N).
- Supplied without end fittings: M6 x 1.0 thread at both ends.
- Same dimensions, 200 N version: 100097.
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift



English spoken
On parle Français

Reviews
There are no reviews yet.