Description of the stainless steel gas spring 100109
The 100109 stainless steel gas spring is an official Dufour Yachts part, made by Ressorts SPEC (AS Raymond / Barnes Group) and fitted as original equipment on Dufour sailing yachts. It is a compression strut: it pushes its rod out with a force of 400 N over a 200 mm stroke, giving firm opening assistance and a secure hold for heavy components on board, such as cockpit lockers, deck hatches and berth lids with storage underneath.
The body and rod are made of 316 stainless steel, the reference grade for the marine environment. The strut does not rust, even when exposed to salt air, spray or the humidity of lockers. With an 8 mm rod and an 18 mm body, it delivers high force in a compact size. The body measures 449 mm, and the overall length between ball socket centres is 485 mm when extended.
Both ends are threaded M6 x 1.0 and fitted with black nylon (PA66 glass-filled) ball sockets that clip directly onto standard 10 mm ball studs. The sockets are rated well above the strut’s force, and they let it swivel freely as the hatch opens and closes, which limits side loads on the rod and seal. The 100109 is delivered complete and ready to install: unclip the worn strut and clip the new one onto the original studs.
Specifications
- Type: Compression gas spring with ball sockets
- Reference: 100109
- Force: 400 N
- Stroke: 200 mm
- Body length (extended, without end fittings): 449 mm
- Length between centres (extended, with end fittings): 485 mm
- Rod diameter: 8 mm
- Body diameter: 18 mm
- Thread: M6 x 1.0 at both ends
- Material: 316 stainless steel body and rod
End fittings & boat compatibility
- End fittings #1 and #2: EFBS004P ball socket, black nylon PA66 GF30, for 10 mm ball stud, length 18 mm
- Brand: DUFOUR – official Dufour Yachts part, reference 100109
- Matching fixings: 100084 stainless ball stud (10 mm, M8), 100108 or 100116 brackets (10 mm ball)
Installation / Maintenance
Installation:
- Prop the hatch open securely, unclip the worn strut from its ball studs and clip the 100109 in its place.
- Mount the strut with the rod pointing down where possible to keep the seal lubricated.
- Check that the hatch opens fully and closes without binding or side load on the rod.
Maintenance:
- Rinse with fresh water after sailing and keep the rod clean. Salt crystals on the rod can damage the seal.
- Check the nylon ball sockets periodically for wear or cracks.
- Never heat, open or drill the body, which is pressurised. A strut that has lost force must be replaced.
Our review
✔️ Pros :
- Official Dufour Yachts part: exact original fit.
- 316 stainless steel body and rod for marine durability.
- High 400 N force in a compact 8/18 mm format.
- Delivered with ball sockets, ready to clip on.
❌ Cons :
- Fixed force of 400 N, not adjustable.
- Fits 10 mm ball studs only.
- The ball sockets are nylon, not stainless steel.
Conclusion
If your Dufour has a strut printed 100109, or one that measures 485 mm between centres with a 200 mm stroke, a 400 N force and sockets for 10 mm ball studs, this is the right replacement. Its stainless construction and firm force suit heavy hatches and lockers, including exposed ones. If a ball stud or bracket is also worn, our matching Dufour fixings are available. If any value differs from your original strut, contact our team before ordering.
Good to Know
- Official Dufour Yachts part.
- Before ordering, compare three values: length between centres (485 mm), stroke (200 mm) and force (400 N).
- End fittings: EFBS004P nylon ball sockets for 10 mm ball studs.
- Matching Dufour fixings: ball stud 100084, brackets 100108 and 100116.
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift



English spoken
On parle Français

Reviews
There are no reviews yet.