Description of the gas spring 081655
The 081655 gas spring is a compression strut made by Ressorts SPEC (AS Raymond / Barnes Group) and supplied as original equipment to the Beneteau group through BJ Technologie. It pushes its rod out with a force of 500 N over a 250 mm stroke, giving firm opening assistance and a secure hold for heavy components on board, such as cockpit lockers, deck hatches and berth lids with storage underneath.
This marine gas strut belongs to the Ressorts SPEC Nitrider range. It has a black-coated body and a rod with a nitrided anti-corrosion surface, plus a modern sealing system designed for long service life. Its 10 mm rod and 23 mm body give it more robustness than smaller formats, which suits frequent use on heavy hatches. The body measures 549 mm, and the overall length between ball socket centres is 609 mm when extended.
Both ends are threaded M8 x 1.25 and fitted with zinc-plated steel ball sockets for 13 mm ball studs. This larger ball size is typical of heavier installations, so check your studs before ordering: 10 mm studs will not fit. The sockets let the strut swivel freely as the hatch moves through its arc. The 081655 is delivered ready to install on the original fixings.
Specifications
- Type: Compression gas spring with ball sockets
- Reference: 081655
- Force: 500 N
- Stroke: 250 mm
- Body length (extended, without end fittings): 549 mm
- Length between centres (extended, with end fittings): 609 mm
- Rod diameter: 10 mm
- Body diameter: 23 mm
- Thread: M8 x 1.25 at both ends
- Finish: black-coated body, nitrided anti-corrosion rod
End fittings & compatibility
- End fittings #1 and #2: EFBS005Z ball socket, zinc-plated steel, M8 x 1.25, length 30 mm
- Compatible ball diameter: 13 mm
- Original equipment: Beneteau group (BJ Technologie)
Installation / Maintenance
Installation:
- Prop the hatch open securely, unclip the worn strut from its ball studs and clip the 081655 in its place.
- Mount the strut with the rod pointing down where possible to keep the seal lubricated.
- Check that the hatch opens fully and closes without binding or side load on the rod.
Maintenance:
- Keep the rod clean and free of salt deposits. Never scratch or paint it, as this damages the seal.
- Check the ball sockets periodically for wear or corrosion.
- Never heat, open or drill the body, which is pressurised. A strut that has lost force must be replaced.
Our review
✔️ Pros :
- Original equipment for the Beneteau group: exact original fit.
- Robust 10/23 mm format for heavy hatches.
- Delivered with steel ball sockets, ready to clip on.
- Nitrided rod with anti-corrosion surface.
❌ Cons :
- Not stainless steel: less suited to permanently exposed outdoor locations.
- Fixed force of 500 N, not adjustable.
- Fits 13 mm ball studs only.
Conclusion
If your boat has a strut printed 081655, or one that measures 609 mm between centres with a 250 mm stroke, a 500 N force and sockets for 13 mm ball studs, this is the right replacement. Check the ball diameter carefully: a similar-looking strut with 10 mm sockets will not clip onto your studs. If in doubt, contact our team before ordering.
Good to Know
- Original equipment for the Beneteau group (BJ Technologie).
- Before ordering, compare four values: length between centres (609 mm), stroke (250 mm), force (500 N) and ball diameter (13 mm).
- End fittings: EFBS005Z zinc-plated steel ball sockets.
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift



English spoken
On parle Français

Reviews
There are no reviews yet.