Description of the stainless steel gas spring 180164
The 180164 stainless steel gas spring is a compression strut made by Ressorts SPEC (AS Raymond / Barnes Group) and supplied as original equipment to the Beneteau group through BJ Technologie. It pushes its rod out with a force of 100 N over a 150 mm stroke, giving gentle opening assistance and a steady hold for light components on board, such as locker lids, cabinet doors, chart table lids and small hatches.
The strut is made of 316L stainless steel, a low-carbon grade with excellent corrosion resistance in the marine environment. It does not rust, even when exposed to salt air, spray or the condensation found in lockers and galleys. With a 6 mm rod and a 15 mm body, it is slim and discreet inside joinery. The body measures 340 mm, and the overall length between ball socket centres is 376 mm when extended. A label on the body shows the reference and force for easy identification.
Both ends are fitted with black nylon (PA66 glass-filled) ball sockets that clip directly onto standard 10 mm ball studs. They let the strut swivel freely as the lid opens and closes, which limits side loads on the rod and seal. The 180164 is delivered complete and ready to install: unclip the worn strut and clip the new one onto the original studs in a few seconds.
Specifications
- Type: Compression gas spring with ball sockets
- Reference: 180164
- Force: 100 N
- Stroke: 150 mm
- Body length (extended, without end fittings): 340 mm
- Length between centres (extended, with end fittings): 376 mm
- Rod diameter: 6 mm
- Body diameter: 15 mm
- Material: 316L stainless steel
End fittings & compatibility
- End fittings #1 and #2: EFBS004P ball socket, black nylon PA66 GF30, for 10 mm ball stud, length 18 mm
- Original equipment: Beneteau group (BJ Technologie)
Installation / Maintenance
Installation:
- Hold the lid open, unclip the worn strut from its ball studs and clip the 180164 in its place.
- Mount the strut with the rod pointing down where possible to keep the seal lubricated.
- Check that the lid opens fully and closes without binding or side load on the rod.
Maintenance:
- Rinse with fresh water from time to time and keep the rod clean. Never scratch or paint it, as this damages the seal.
- Check the nylon ball sockets periodically for wear or cracks.
- Never heat, open or drill the body, which is pressurised. A strut that has lost force must be replaced.
Our review
✔️ Pros :
- Original equipment for the Beneteau group: exact original fit.
- 316L stainless steel: no rust, even in exposed locations.
- Slim 6/15 mm format, discreet in joinery.
- Delivered with ball sockets, ready to clip on.
❌ Cons :
- Fixed 100 N force, for light lids only.
- Fits 10 mm ball studs only.
- The ball sockets are nylon, not stainless steel.
Conclusion
If your boat has a strut printed 180164, or one that measures 376 mm between centres with a 150 mm stroke, a 100 N force and nylon sockets for 10 mm ball studs, this is the right replacement. Its 316L stainless construction makes it a long-lasting choice for light lids, even in damp or exposed locations. If any value differs from your original strut, contact our team before ordering.
Good to Know
- Original equipment for the Beneteau group (BJ Technologie).
- Before ordering, compare three values: length between centres (376 mm), stroke (150 mm) and force (100 N).
- End fittings: EFBS004P nylon ball sockets for 10 mm ball studs.
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift



English spoken
On parle Français

Reviews
There are no reviews yet.