Description of the gas spring 100090
The 100090 gas spring is an official Dufour Yachts part, made by Ressorts SPEC (AS Raymond / Barnes Group) and fitted as original equipment on Dufour sailing yachts. It is a compression strut: it pushes its rod out with a force of 150 N over a 150 mm stroke, giving smooth opening assistance and a steady hold for light-to-medium components on board, such as locker lids, cabinet doors, chart table lids and small hatches.
This marine gas strut belongs to the Ressorts SPEC Nitrider range. It has a black-coated body and a rod with a nitrided anti-corrosion surface, plus a modern sealing system designed for long service life. With a 6 mm rod and a 15 mm body, it is slim and discreet inside joinery. The body measures 340 mm, and the overall length between ball socket centres is 376 mm when extended.
Both ends are threaded M6 x 1.0 and fitted with black nylon (PA66 glass-filled) ball sockets that clip directly onto standard 10 mm ball studs. They let the strut swivel freely as the lid opens and closes, which limits side loads on the rod and seal. The 100090 is delivered complete and ready to install: unclip the worn strut and clip the new one onto the original studs in a few seconds.
Specifications
- Type: Compression gas spring with ball sockets
- Reference: 100090
- Force: 150 N
- Stroke: 150 mm
- Body length (extended, without end fittings): 340 mm
- Length between centres (extended, with end fittings): 376 mm
- Rod diameter: 6 mm
- Body diameter: 15 mm
- Thread: M6 x 1.0 at both ends
- Finish: black-coated body, nitrided anti-corrosion rod
End fittings & boat compatibility
- End fittings #1 and #2: EFBS004P ball socket, black nylon PA66 GF30, for 10 mm ball stud, length 18 mm
- Brand: DUFOUR – official Dufour Yachts part, reference 100090
- Matching fixings: 100084 stainless ball stud (10 mm, M8), 100108 or 100116 brackets (10 mm ball)
Installation / Maintenance
Installation:
- Hold the lid open, unclip the worn strut from its ball studs and clip the 100090 in its place.
- Mount the strut with the rod pointing down where possible to keep the seal lubricated.
- Check that the lid opens fully and closes without binding or side load on the rod.
Maintenance:
- Keep the rod clean and free of salt deposits. Never scratch or paint it, as this damages the seal.
- Check the nylon ball sockets periodically for wear or cracks.
- Never heat, open or drill the body, which is pressurised. A strut that has lost force must be replaced.
Our review
✔️ Pros :
- Official Dufour Yachts part: exact original fit.
- Delivered with ball sockets, ready to clip on.
- Slim 6/15 mm format, discreet in joinery.
- Nitrided rod with anti-corrosion surface.
❌ Cons :
- Not stainless steel: best suited to interior or sheltered locations.
- Fixed force of 150 N, not adjustable.
- Fits 10 mm ball studs only.
Conclusion
If your Dufour has a strut printed 100090, or one that measures 376 mm between centres with a 150 mm stroke, a 150 N force and nylon sockets for 10 mm ball studs, this is the right replacement. It suits interior lockers and furniture lids, where it gives a smooth, controlled opening. If a ball stud or bracket is also worn, our matching Dufour fixings are available. If any value differs from your original strut, contact our team before ordering.
Good to Know
- Official Dufour Yachts part.
- Before ordering, compare three values: length between centres (376 mm), stroke (150 mm) and force (150 N).
- End fittings: EFBS004P nylon ball sockets for 10 mm ball studs.
- Matching Dufour fixings: ball stud 100084, brackets 100108 and 100116.
- Manufacturer: Ressorts SPEC. See all Ressorts SPEC products and our marine gas springs.

Electrical
Marine Batteries
Mechanical
Gas Springs
Seat suspensions
Table solutions
TV Lift



English spoken
On parle Français

Reviews
There are no reviews yet.